Landis 4R Plain OD Grinder
Serial Number: 819-13
Model 4R
SPECIFICATIONS:
18″ Swing
72″ Between Centers
30″ x 4″ x 12″ Diameter Grinding Wheel
Wheel Guard Can accommodate unto an 8″ Wheel Width
Jarno #14 Center Tapers
2-240 IMP Table Traverse Rate
15HP Spindle Drive Motor
Behind the Wheel Profile Dresser
Plunge Cycle
Tarry Timer Left & Right at Table Reversal
Variable Speed Headstock Drive
Dead Center Head Stock
Coolant Pump & Tank
Free Standing Electrical Panel – 3/60/480 Volt
Manuals & Prints
Cleaned, Painted & Cycled
Table Flaked
Approx Weight: 18,200lbs.
Machine Dimensions: 19′ 2″ L-R x 6′ F-B
14″ x 96″. LANDIS. PLAIN. O.D. GRINDER
MODEl: CH
SPECIFICATIONS:
14″ Swing over table
96″ between centers
Dead Center Headstock ( NEW A.C. INVERTER VARI-SPEED MOTOR & CONTROLLER)
Hand Operated Tailstock
30″ x 12″ x 4″ Grinding Wheel Capacity
RAPID TRAVERSE ON GRINDING WHEEL SLIDE
Hydraulic table travel with automatic pick feed
Self Contained Coolant Pump & Tank
Free Standing Electrical Panel
Cleaned, Painted & Cycled
NOTE: TABLE WAYS HAVE BEEN SCRAPPED & FLAKED
WAYS LOOK EXCELLENT
WHEEL SLIDE WAYS LOOK VERY GOOD
HYDRAULICS VERY QUIET
NEW 20 HP. ELECTRIC MOTOR ON GRINDING SPINDLE
NEW. A.C. INVERTER MOTOR ON HEADSTOCK WITH VARI-SPEED CONTROLS
Norton Plain OD Grinder
Model CTU
SPECIFICATIONS:
25″ Swing. Over. Table
20″ Between Centers
Hydraulic Table Travel
Pick Feed
Automatic Plunge Cycle on Grinding Wheel Slide
Headstock ( Live center / Dead center combination )
Tailstock
30 x 12 x 3. Grinding Wheel Capacity
Self Contained Coolant Pump & Tank
Attached Electrical Panel
Landis 14″ x 96″ Plain OD Grinder
Model: CH
SPECIFICATIONS:
SWING: 14″
DISTANCE BETWEEN CENTERS: 96″
GRINDING WHEEL DIAMETER: 30″
GRINDING WHEEL WIDTH: 3″
GRINDING WHEEL HOLE DIAMETER: 12″
TABLE TRAVERSE SPEED (VARIABLE): 2 TO 240 IPM
Norton 10″ x 96″ CTU Plain Cylindrical Grinder
SPECIFICATIONS:
10″ Swing Over Table
96″ Distance Between Centers
30″ x 3″ x 12″ Grinding Wheel Capacity
Plunge Cycle
Manual Tailstock
Work Head Speed: 30 – 75 RPM
Work Head Center Taper: No. 14 Jarno
Table Speeds: 2″ – 240″ IPM
Attached Electrical
Machine Dimensions: 124″ x 246″ Floor Space
Machine Weight: 18,000LBS. Shipping Weight
This machine can have Risers installed to increase swing capacity.
Norton 10″ x 72″ CTU Plain Cylindrical Grinder
Serial Number: 27725
SPECIFICATIONS:
10″ Swing Over Table
72″ Distance Between Centers
24″ x 8″ x 12″ Grinding Wheel Capacity
Manual Tailstock
Attached Electrical
Landis 1R 6×18 Plain Cylindrical Grinder
Serial Number: 875-38
Specifications:
6″ Swing
18″ Center Distance
16″ x 1″ x 5″ Grinding Wheel Size
Hydraulic Table Traverse Speeds: 2″ – 200″ IMP
Tarry Left & Right
Pick Feed Left – Right – Left & Right
Spark out Timer
Auto Plunge Cycle w/ Comp
Dead Center Headstock
Manual Tailstock
Behind Wheel Guard Dresser w/ Comp
Bijur One Shot Lube
Attached Electrical 460/3/60
1-USED SMTW MODEL H147 25″ X 160″ PLAIN CYLINDRICAL OD GRINDER
SERIAL NUMBER 129
APPROX. DATE OF MFG. 1997
RATED WORK PIECE CAPACITY 25″ X 157″
CENTER HEIGHT 13.8″
MAX. WORK LOAD 3,000 LBS
*SPINDLE HEAD AREA OF MACHINE*
SPINDLE HEAD MOTOR 20 HP (15 KW)
WHEEL SIZE MAX. 30″ X 3″ WIDE X 12″ HOLE
WHEEL SPEED 890 RPM
SURFACE SPEED 6990 FPM
RAPID TRAVEL 30 FPM
HANDWHEEL REV. 0.05″
HANDWHEEL DIV. .0001″
MAX. TRAVEL RP 4″
MAX. TRAVEL HW 10″
SPINDLE BEARINGS 4 SHOE HYDRODYNAMIC
SPINDLE TAPER 1.5 TAPER
OIL RESERVOIR 12 GAL @ 2 ISO VISCOSITY GRADE
*WORK TABLE AREA OF MACHINE*
SWIVEL -1 DEGREE/+3 DEGREES
FEED RANGE 4 TO 157 FPM
MAX. TRAVEL 160″
TABLE ANGLE 20 DEGREES SLANT
*WORKHEAD AREA OF MACHINE*
MAIN MOTOR ON WORK HEAD 4/6 HP (2 SPEED)
TAPER IN WORKHEAD 6 MT
WORK HEAD RPM 22,44,60,84,120,168
*TAILSTOCK*
TAPER 6 MT
QUILL TRAVEL 2.76″
DRESSING SOLID MOUNT
*HYDRAULIC UNIT*
1.5 HP MOTOR
FLOW RATE 7 GPM
PRESSURE 142 TO 184 PSI
RESERVOIR CAPACITY 55 GALLONS 32 ISO VISCOSITY GRADE
EQUIPPED WITH:
SINGLE AXIS DRO ON SPINDLE HEAD INFEED
TAILSTOCK
3 STEADY RESTS
ASSORTED LEVELING PADS
EXTERNAL ELECTRICAL PANEL
EXTERNAL HYDRAULIC POWER UNIT
MACHINE DIMENSIONS 484″ LONG X 103″ WIDE X 81″ TALL
APPROX. GROSS WEIGHT 32,500 LBS
Norton 10″ x 72″ CTU Plain Cylindrical Grinder
SN 26974
Stock Number: 5334
SPECIFICATIONS:
10″ Swing Over Table
72″ Distance Between Centers
24″ x 8″ Wide GW
Table Mount Dresser
Hydraulic Tail Stock
Barnes Coolant with Magnetic & Fabric Separator
Attached Electrical
40hp main spindle drive
Machine Video
(1) Used Warner & Swasey (Norton) 24″ x 120″ Plain Cylindrical Grinder
Serial Number: 28745
Stock Number: 5295
SPECIFICATIONS:
24″ Swing Over Table
120″ Distance Between Centers
30″ Dia x 5″ Wide Grinding Wheel Guard Capacity
15 HP Spindle Drive Motor
Automatic Plunge Cycle
Dwell Cycle Left & Right at Table Reversal
Pick Feed at Table Reversal
Variable Speed Headstock Drive
Manual Tailstock
Manual Oscillating Attachment on Grinding Wheel
Attached Electrical Panel
Self Contained Coolant System w/ Pump
