Blanchard 22K 42 Vertical Spindle Rotary Surface Grinder
Serial Number: 13255
SPECIFICATIONS:
42″ Magnetic Chuck Diameter
24″ Approximate Range Over Chuck With New Wheel
22″ Diameter of Wheel Chuck, Segmented
48″ Swing Inside Water Guards
720 RPM Wheel Speed
(6) Chuck Speeds 5,7,10,15,20 & 27 RPM
Automatic Downfeeds Feed 0 to 70 IN/MIN
50 HP, 3 Phase, 60 Cycle
Neutrofier II Chuck Control
Floor Space: 13.5″L x 8.4″W
Height: 8.7″ Min., 9.1″ Max.
Approx. Weight: 14,250 lbs.
Blanchard Mdl. 32-60 Vertical Spindle Rotary Surface Grinder
Serial Number: 11267
SPECIFICATIONS:
60” Chuck – Excellent Chuck Life – 3/4″
72″ Swing Inside Guards
32” Segmented Wheel
75HP Drive
28″ Vertical Height Over Chuck
.001″ – .100″ IMP Course Feed Rate
.0001″ – .010″ IMP Feed Range
Neutrol II Chuck Control
Swing Arm Dresser
Dry Base – with tank & pump
Ways look ok
480 Volt
Blanchard Mdl. 18-36 Vertical Spindle Rotary Surface Grinder
SPECIFICATIONS:
Serial Number: 7712
36” Chuck
18” Segmented Wheel
Incremental Down Feed
Swing Arm Dresser
Table Speeds: 6,9,12,18,25,33 RPM
Neutrol Chuck Control
ARTER B-24 HORIZONTAL SPINDLE ROTARY SURFACE GRINDER Serial Number: 3420 Stock Number: 2116 SURFACE DIAMETER OF MAGNETIC CHUCK …………….. 25″ MAX. SWING INSIDE GUARDS ……………………… 36″ VERTICAL CAPACITY UNDER FULL 20″ WHEEL …………. 8″ TILT OF TABLE FOR CONVEX OR CONCAVE GRINDING ……. 10 DEG. GRINDING WHEEL SIZE ………………………….. 20″D X 12″BORE X 2″WIDTH CHUCK ROTATION SPEED …………………………. UP TO 75 RPM GRINDING WHEEL SPINDLE SPEED ………………….. 950 RPM HANDWHEEL FOR RAISING & LOWERING WORK TABLE IS CALIBRATED IN INCREMENTS OF ………………. 0.005″ FINE FEED KNOB FOR RAISING & LOWERING WORK TABLE IS CALIBRATED IN INCREMENTS OF ………………. 0.0001″ APPROXIMATE MACHINE WEIGHT ……………………. 10,700 LBS Machine Has been Dis-Assembled, New Rulon on the Table. Spindle Run Quiet * Issues with the Feed Mechanism and Some Play in the Ram
Arter Horizontal Rotary Surface Grinder
Model: E-30
New: 1987
Serial Number: 4028
Stock Number: 2101
SPECIFICATIONS:
30″ Diameter Chuck
18″ x 5″ x 5″ Grinding Wheel
Table Reciprocating Speeds: 5 – 225 IPM ( Inf Variable )
Table Rotation Speeds: 5-300 RPM ( Inf Variable )
Wheel Speed: 1400 RPM
Downfeed Speed: 0 – .040″ IPM ( Inf Variable )
Rapid Downfeed: Fast 3″ IPM / Slow 0-2″ IPM ( Inf Variable )
20 HP Main Drive Motor
Table Job
Hydraulic Over the Wheel Dresser
Magna Lock Variable Pull Chuck Control
Free Standing Hydraulics
Approx 11,000 LBS.
Full Set of Prints & Parts Catalog
- New Electrical Being Installed
- Cleaned, Painted & Cycled
Blanchard 20D -36 Rotary Grinder
Serial 12008
Electromagnetic Chuck Diameter 36″
Max Swing inside Guards
20″ Diameter Segmented Grinding Wheel
Max. Height under New Wheel 18″
Spindle Drive Motor 40 HP
Neutrofier Vari Chuck Control
Trabon Lube
(6) Table Speeds 6, 9, 12, 18, 25 & 33 RPM
Power Rapid DownFeed & Elevation
Incremental Downfeed
Swing Arm Dresser
Attached Electrical 220/3/60
Trabon One Shot Lubrication
220/440 Volt, 3 phase
CLEANED, PAINTED, AND CYCLED
Item I: (Lower Unit)
A. Bed ways, rotary table ways, in excellent condition
Item II: Upper Unit (Column & Head)
A. Spindle runs and sounds like new
Item III: Lube System
A. Has auto lube pump, checked all lines & fittings
Item IV: Electrical
A. All motors, switches, buttons, enclosures, seal tite, fittings, checked, repaired as needed
Item V: Mechanical
A. Inspect all feed screws, nuts gears, bushings, seals, bearings, repaired as needed
Item VI: Appearance
A. Sand blast, clean, fill, sand, prime, & paint machine to factory spec’s
Delivery: Immediate
Blanchard 18-30 Vertical Spindle Rotary Surface Grinder
Serial Number: 5263
SPECIFICATIONS:
18″ Grinding Wheel
30″ Chuck
220/440 Volt, 3 phase, 25 HP
Chuck Life 7/16 top
(6) Ranges of Chuck Speeds, 6, 9, 12, 18, 25, 33 RPM
Feed 0.004 – 0.076 IPM
720 RPM Wheel Speed
Floor Space 116″L x 66″W x 8-5″ Max Height
Approx. Weight 11,800 lbs
Cleaned, Painted, and Cycled
All feeds and speeds are functional
Spindle runs and sounds good
Ready for immediate delivery
Blanchard 20D36 Vertical Spindle Rotary Surface Grinder
Model: 20D36
Serial Number: 12008
SPECIFICATIONS:
20” Segmented Wheel
36” Chuck – 3/8” Life
Neutrofier Vari Chuck Control
Trabon Lube
(6) Table Speeds 6, 9, 12, 18, 25 & 33 RPM
Power Rapid DownFeed & Elevation
Incremental Downfeed
Swing Arm Dresser
Attached Electrical 220/3/60
* Machine is currently being Stripped, Cleaned & Painted
(1) Used 60” Blanchard Vertical Spindle Rotary Surface Grinder
Model: 32-60
Serail Number: 11411
Specifications:
60” Diameter Magnetic Chuck
32” Segmented Grinding Wheel
Power Table Traverse
Incremental Downfeed Neutrofier
External Coolant Tank & Pump Free
Standing Electrical Panel
3/4” Chuck Life
100 HP Spindle Motor
