Parker Majestic 14″ x 30″ 2C Universal Cylindrical / Internal Grinder
Serial Number: 00069-2C-05
New: 2005
SPECIFICATIONS:
14″ Swing
30″ Distance Between Centers
OD Grinding Wheel: 12″ x 1″ x 5″
1 HP Variable Speed Headstock
5 HP Variable Speed OD Grinding Wheel Drive
3 HP Variable Speed ID Grinding Wheel Drive
Variable Speed Table Traverse
Manual Driven Ballscrew Cross feed – Hand Wheel Graduated “.0005 – Precision Graduated .00005”
7º Table Swivel
90º Headstock Swivel
One Shot Lubrication
Attached Electrical Panel – 480 V / 60 / 3
EQUIPPED WITH:
5″ Sine Bar Headstock
Heidenhain Digital Read Out
Paper Filtration System w/ Gusher Pump & Tank
3 Point Center Rest
8″ 3 Jaw Chuck
10″ Magnetic Chuck
Splash Guards
Machine Dimensions:
104″ x 41″ x 46″
Approx Weight: 5200 LBS.
GER Universal OD Grinder w/ ID Attachment
Model: RHC-1000
Serial Number: 82/2008
SPECIFICATIONS:
Swing: 12″
Center Distance: 40″
Grinding Wheel Motor: 5 HP
Internal Grinding Spindle Motor: 1 HP
OD Grinding Wheel Size: 16″ Did x 5″ Width x 5″ Hole
Headstock Drive Motor: 1 HP
Hydraulic Pump: 1.5 HP
Pickfeed at Table Reversal
Automatic Plunge Cycle
Manual Tailstock
Coolant Tank & Pump
Internal Grinding Attachment w/ Spindle
Coolant Tank & Pump
220/3/60
Operators Manuals & Prints
GER Universal OD Grinder w/ ID Attachment
Model: RHL-600
Serial Number: 81 / 91
SPECIFICATIONS:
Swing: 10″
Center Distance: 24″
Grinding Wheel Size: 16″ x 3″ x 5″
Grinding Wheel Motor: 5.5 HP
Work Head Drive Motor: 1 HP
Hydraulic Motor: 1.5 HP
Plunge Cycle
Pick Feed at Table Reversal
Internal Grinding Spindle Attachment
Coolant Pump & Tank
220/3/60
Approx Weight: 5,500LBS.
Cincinnati Milacron R-77 Plain OD Grinder
Chevalier Universal Cylindrical OD Grinder
Model: CGP-816
Serial Number: 2040317
Condition: Like New
Operating Hours: 142
Purchased New in 2010
Control Type: Mitsubishi Pro-Face Digital w/ DRO
PLC controls the In-Feed Functions, Rapid, Rough & Fine Feeds & Retraction at end of Cycle
Spindle Head: MT:3 / +
Attachment for Chuck
1/4 HP Coolant Pump System
Magnetic Coolant Separator 20L
Paper Band Filter 20L
Table Swivel Angle: -3º, +12º
Distance between Centers: 15.7º
Swivel over Table: 7.9”
Max. load between centers: 132lbs
Max. External Grinding: 7.09”
Wheel Head Swivel Angle: ±30º
Wheel Head Manual Distance: 5.2”
Wheel Size: Ø12” OD x 1.5” W x Ø5” ID
Wheel Speed: 60Hz: 2,495 RPM
Wheel Spindle Motor: 3 HP
Spindle Speed: 10 – 300 RPM
Workhead Spindle Motor: 1HP
Manual Tailstock
Currently Set Up with a Collet Fixture on Headstock, Centers available with Machine
Power: 23A/230V, 3-Phase
Overall Dimensions: 86.6”L x 70”W x 60.7”H
Weight: 4,400lbs
Parker Majestic 14″ x 30″ 1C OD / ID Combination Cylindrical Grinder
Model: 1C
Serial Number: 6314-1C-99
New: 1999
GENERAL CATALOG SPECIFICATIONS
OVERALL DIMENSIONS (WXDXH) 104 IN X 41 IN X 46 IN
MACHINE WEIGHT (NET) 5200 LBS (2358 KG)
MAX PART DIAMETER 14 IN (355.6 MM)
DISTANCE BETWEEN CENTERS 30 IN (762 MM )
WORKTABLE SIZE 5 IN X 50 IN (127 MM X 1270 MM)
TABLE SWIVEL 7 DEGREES
WORKHEAD SPINDLE
SPEED 0-1000 RPM
SPINDLE NOSE PARKER TAPER – ACCEPTS 5C COLLETS
DRIVE MOTOR 1 HP@1,750/200 RPM
MANUALLY PIVOTING WORKHEAD (B-AXIS) – ACCURACY 0.0005 DEGREES
POWER
POWER REQUIREMENT 230, OR 480 VAC – 50/60 HZ
POWER CONSUMPTION 6 KVA
MAX. CURRENT 30 A
TOTAL POWER RATING 10 HP (7.5 KW)
TABLE AXIS
MANUAL AND VARIABLE SPEED ELECTRIC TABLE DRIVE
HAND SCRAPED TURCITE COATED VEE & FLAT WAY SYSTEM
TOTAL TRAVEL 30 IN (762 MM)
TABLE FEED MOTOR 3/4 HP @ 1,750/400 RPM
TABLE SWIVEL 7 DEGREES
CROSSFEED AXIS
MANUAL DRIVEN BALLSCREW
PRECISION ROLLING ELEMENT LINEAR MOTION BEARING
CLOSED LOOP POSITIONING WITH HEIDENHAIN GLASS SCALE FEEDBACK
TOTAL TRAVEL 7 IN (177.8 MM)
EQUIPPED WITH
SWING AROUND OD / ID UNIVERSAL GRINDING HEAD
14″ DIAMETER GRINDING WHEEL CAPACITY
8″ (6) JAW CHUCK
5″ SINE BAR HEADSTOCK
MANUAL TAILSTOCK
TABLE MOUNTED DRESSER
DANFOSS VTL 2000 VARIABLE SPEED DRIVES
COOLANT PUMP & TANK
ATTACHED ELECTRICAL PANEL 22/3/60
ELECTRICAL DRAWINGS & MANUALS
MACHINE IS IN EXCELLENT CONDITION – (1) ONE OWNER – ORIGINAL SCRAPING & PAINT
SMALL ONE MAN JOB SHOP
(1) 20″ NORTON CTU PLAIN OD GRINDER ( RE-CONDITIONED )
SPECIFICATIONS:
30″ x 12″ x 3″ WHEEL CAPACITY
20″ SWING OVER TABLE
36″ CENTERS
LIVE HEADSTOCK w/ NEW VARIABLE SPEED DRIVE & MOTOR
HAND OPERATED TAILSTOCK W/ LIVE CENTER CAPABILITY
AUTO PLUNGE CYCLE ….. ( RAPID INFEED TO POSITIVE STOP )
HYDRAULIC TABLE TRAVEL
Chuck & Adaptor Plate Installed
SCOPE OF WORK TO RECONDITION NORTON GRINDER
1) SEMINOLE MACHINERY to disassemble grinder, clean and check base for excessive wear and stress fractures.
2) Clean and inspect component parts, replace any components parts that are worn or broken with remanufactured parts.
3) Grind, Scrape and Flake traverse table ways to original tolerance.
4) Grind, Scrape and Flake cross slide ways to original tolerance.
5) Re-build grinding wheel spindle as necessary.
6) Re-build hydraulic pump. Re-pair as necessary all hydraulic valves. NEW Filters & Hoses
7) Re-build lubrication system as necessary with New & Rebuilt PARTS
8) Re-build HEADSTOCK as necessary, Install NEW Headstock Variable Speed Drive & Motor
9) Re-build TAILSTOCK AS NECESSARY
10) Hand feed assembly to be completely disassembled, cleaned and inspected.
INSTALL NEW BEARINGS & NEW COMPONENTS
11) Electrics: New or rebuilt components as necessary
ALL ELECTRIC MOTORS REBUILT WITH NEW BEARINGS
All push bottoms to be repaired as necessary.
12) Coolant tank cleaned and checked.
COOLANT PUMP REBUILT
13) MACHINE to be thoroughly cleaned and painted with industrial grade Dupont Dulex epoxy paint. Color of your choice.
Landis 24″ x 120″ Plain OD Grinder
SPECIFICATIONS:
24″ Swing
120″ Distance Between Centers
30″ Diameter Grinding Wheel
Variable Speed Workhead
Hydraulic Table Travel
Manual Tailstock
20HP Spindle Drive
(2) Steady Rests
Free Standing Electrical
Cincinnati Milacron R-77 Hydraulic OD Grinder
10″ x 31″ CINCINNATI MILACRON
CYLINDRICAL GRINDER
Model R-77
STANDARD SPECIFICATIONS
Maximum distance between centers: 31″
Maximum swing over table: 10″
Maximum weight of work piece between centers: 165 lbs.
Maximum weight of chuck held work: 44 lbs.
TABLE
Table traverse speeds, infinitely variable: 2-240 IPM
Table traverse per revolution of hand wheel: 0.1″ – .5″
Minimum movement necessary to reverse table: 5/32″
Maximum swivel of table: +/-14 degree
HEAD STOCK
Number of speeds: Infinite
Speed range: 60-500 RPM
Diameter of bore in spindle: 1 1/2″
Head stock spindle nose-American Lathe Standard: 5″
Center taper: #6 Jarno
Swivel: 0-90 Degree
FOOT STOCK
Center taper: #6 Jarno
Quill retraction: 8′
WHEEL HEAD
Swivel: +/-45 Degrees
Rapid advance stroke: 2″
Manual infeed per hand wheel revolution (dia.): 0.050″
Auto pick feed on diameter: 0.0002″ – .0016″
Hand lever compensation on diameter: 0.0001″
Grinding wheel:
Standard wheel size: 16″ O.D. x 2″ wide x 5″ hole
Wired 230/3/60
Approx 5,100lbs.
