Moore G-18 Jig Grinder

  |   By  |  0 Comments

Moore G-18 Jig Grinder
Moore Model: G-18
S/N# G-2194

SPECIFICATIONS:
11″ x 24″ Table
Travel 11″ x 18″
Table top to wheel collet 2″ to 18
Spindle to column ways 10″
Max spindle speed 40,000 rpm
Grinding capacity 3/16″ to 5″
Sony 2 axis DRO

(2) Additional Grinding Spindle Heads Available

Moore / NASA #3 4 Axis CNC Jig Grinder

  |   By  |  0 Comments

Moore / NASA #3 4 Axis CNC Jig Grinder

SPECIFICATIONS:
Table size:  11″ X 24″
Table travels:
Longitudinal – 17.5″
Cross – 10.5″
Table to wheel collet:  18″ max.,  2″ min.
Spindle to column ways:  10″
Spindle travel (U Axis):  3 5/8″

MACHINE EQUIPPED WITH:
Fagor 8030 4 Axis (X,Y,C and U) CNC controls, Nasa Model AGS-3
Roller bearing ways on X and Y Axes
Moore 40,000  RPM spindle
Electric motors and control

Dimensions:  FB X RL – 90″ X 85″
Height:  102″
Est. weight:  4900#

Heald 273A Universal Internal Grinder

  |   By  |  0 Comments

(1) USED HEALD 273A UNIVERSAL INTERNAL GRINDER

Model: 273A
Serial Number: 42180

SPECIFICATIONS:
Swing over table: 24.5″″
Hole length ground: 16”
Max Table Travel: 20”
Hole diamter ground: 18”
Included angle taper: 180 Degrees
Grinding speed: 0 – 18 FPM
Workhead Speed: 0 – 500 RPM ( Variable )
Crossfeed Increments: .0001” – .0005”

EQUIPPED WITH:
Red Head  Spindle – RPM / TBD
4 position stop
Hydrostatic ways
Cross sliding workhead
Dresser
Sine bar attachment
12″ T-Slotted Face Plate
Coolant Tank & Pump

220/3/60 Electrics

Landis 1R Universal OD Cylindrical Grinder w/ ID Attachment

  |   By  |  0 Comments

(1) USED LANDIS 10” X 20” 1R UNIVERSAL CYLINDRICAL GRINDER W/ ID ATTACHMENT
Serial Number: 884-57

SPECIFICATIONS:
Nominal work swing: 10”
Nominal distance between centers: 20”
Table traverse speed: 2 to 240 IPM
Grinding wheel size: 12” diameter x 1” wide x 5” hole
Grinding wheel max width: 1.5”
Grinding wheel spindle motor: 5 HP
Workhead speeds: 30 to 150 RPM
Grinding wheelhead swivel: upper & lower : 90 Degrees each way
Headstock center: #10 Jarno
Footstock center: #6 Jarno
Footstock center movement: lever operated
Diameter of hole in spindle: 1”
Headstock swivel: 120 Degrees
Headstock spindle nose: 5A-2

EQUIPPED WITH:
Swing Down ID Spindle
Table Traverse
Tarry timers left and right reversal
Attached electrical panel

Parker Majestic No. 1 ID Grinder

  |   By  |  0 Comments

Parker Majestic No. 1 Internal Grinder

Specifications
Swing Over Table: 12″
Table Swivel: 7 Degrees
Table Travel: 16″
Table Speed (Variable): 0- 240 IPM
Cross Feed Travel: 3 1/2″
Cross Feed Adjustment: 4″
Workhead:
Speeds (Variable): 0- 240 RPM
Hole Through Spindle: 1 1/4″
Spindle Nose: #6 Jarno
Dimensions (L x W x H): 69″ x 40″ x 57″
Weight: 3,750 Lbs.
Equipped with
– 5″ Sine Bar on Headstock
– Power Table Retraction
– One Shot Lube System
– Coolant System w/ Pump
– Horsepower: 1 1/2

Heald 72A Extended Bridge Internal Grinder

  |   By  |  0 Comments

Heald 72A Extended Bridge Internal Grinder

SPECIFICATIONS
Hydraulic Cross Slide – Rapid Only
55” T-Slot
36” Bridge
11.5” Quill x 2” Die ( 16” overall )
30” Swing over table
24” Swing over bridge
12” 3 Jaw Chuck
41” Table Travel Rack
5HP Spindle Drive Motor
Dresser

Parker Majestic 2U Combination ID/OD Grinder – Remanufactured 2021

  |   By  |  0 Comments

IMG

(1) Parker Majestic 2U Combination ID/OD Grinder – Remanufactured 2021

New: Remanufactured 2021

Specifications:
Swing: 12″
Center Distance: 28″
Table Speeds: 3-30″ IPM
Headstock Swivel: 90˙
Headstock Speeds: ( Variable ) 50-450 RPM
Crossfeed Graduated: 0.50″
Precision Dial: 0.000050″
Coolant System
Approx Floor Space: 41″ x 124″
Approx Weight: 3,800 lbs.

Equipped With:
Swing Around ID / OD Spindles
5″ Sine Bar on Headstock
Compound Universal Swivel Slides Under Grinding Spindle Assemblies
P & G One Shot Lubrication System

Scope of Remanufacturing – 2021
New D.C motor drive VARI-Speed on headstock
New D.C motor drive VARI-Speed on table drive
New lead screw in cross slide
Compound universal (2) swiveling slides under Grinding wheel
New P & G One Shot Lube System
ALL NEW ELECTRICS IN PANEL, PUSH BUTTONS, AND MOTORS
COMPLETELY FLAKED & SCRAPPED TO NEW TOLERANCE
SPINDLES COMPLETE REBUILD WITH NEW BEARINGS

Heald 273A Internal Universal Grinder 12″ Extended Base

  |   By  |  0 Comments

(1) USED HEALD 273A UNIVERSAL INTERNAL GRINDER

Model: 273A
Serial Number: 45289

SPECIFICATIONS:
Swing over table: 28.5″″
Hole length ground: 16”
Max Table Travel: 20”
Hole diamter ground: 18”
Included angle taper: 180 Degrees
Grinding speed: 0 – 18 FPM
Workhead Speed: 0 – 500 RPM ( Variable ) – NEW Baldor Reliance Drive & Motor 2020
Crossfeed Increments: .0001” – .0005”

EQUIPPED WITH:
12″ Extended Base
4″ Factory Riser Blocks to Achieve Larger Swing
5″ Hole Through Workhead
Red Head Spindle
Chuck
4 position stop
Dresser
Plunge Cycle
Hydrostatic ways
Cross sliding workhead
Sine bar attachment
Coolant Tank & Pump
440/3/60

New Screw & Nut installed in Feed Box 10/2020

Parker Majestic IC Combination OD/ID Grinder Re-Conditioned

  |   By  |  0 Comments

IMG

SCOPE of Re-Conditioning

• Rebuild Headstock – New Bearings & Rebuild Drive Motor
• ID Spindle Rebuilt
• OD Spindle Checked & Tested for Run Out ( Excellent Condition )
• Rebuild Table Drive Motor
• Install New Cross Feed Screw & Nut
• Install New Meters & One Shot Lubrication Pump
• Ground, Scraped & Flaked Table Ways / Bed Ways & Cross Slide
• New Rulon  Installed
• Tailstock Rebuilt
• Repair & Replace all Electrical Components & Push Buttons as Required
• Test & Flush Coolant System
• Machine Completely Disassembled, Stripped & Painted to Customers Color Choice

(1) Used Parker Majestic Universal ID / OD Grinder – Re-Conditioned

Model: 1C  Year: Re-Conditioned
Serial Number 1918-1C-65

Specifications:

12” x 24” Capacity
Vari Speed Headstock
Power Table Table Travel ( Variable Speed – Pulley )
Swing Around ID Spindle
1.5 HP Spindle Motor
5″ Sine Bar on Headstock
Coolant Pump & Wet Base