Parker Majestic 12″ x 28″ 2C Universal Cylindrical / Internal Grinder
Serial Number: 2472-2C-87
New: Rebuilt 2024
SPECIFICATIONS:
14″ Swing
28″ Distance Between Centers
OD Grinding Wheel: 12″ x 1″ x 5″
Variable Speed Headstock
Variable Speed Table Traverse
7º Table Swivel
90º Headstock Swivel
One Shot Lubrication
Attached Electrical Panel – 460 V / 60 / 3
EQUIPPED WITH:
5″ Sine Bar Headstock
3 Jaw Chuck
Coolant in Base w/ Pump
Machine Dimensions:
104″ x 41″ x 46″
Approx Weight: 5200 LBS.
Scope of Remanufacturing – 2024
New motor drive VARI-Speed on headstock
New motor drive VARI-Speed on table drive
New lead screw in cross slide
New One Shot Lube System
ALL NEW ELECTRICS IN PANEL, PUSH BUTTONS, AND MOTORS
COMPLETELY FLAKED & SCRAPPED TO NEW TOLERANCE
SPINDLES REBUILT
Heald Long Nose Motorized Internal Grinding Spindle
SPECIFICATIONS:
43” Shaft / Quill Length
4.5” Dia
220 Volt
5HP / 2.5 HP
2 Speeds 3500 / 1750 RPM
Currently wired for one speed 3500 RPM
Parker Majestic 16C Universal OD / ID Grinder
Serial No. 2036-16C-67
SPECIFICATIONS:
Swing Over Table………………………………………………….12″
Distance Between Centers…………………………………………..16″
Table Working Surface…………………………………………5″ x 38″
Power Table with Reciprocator………………………………………Yes
Tabel Swivel………………………………………………..7 Degrees
Table Travel……………………………………………………..24″
Cross Feed Travel………………………………………………3-1/2″
Cross Feed Adjustment………………………………………………4″
Cross Feed Handwheel Graduations………………………………..0.0005″
Cross Feed Precision Dial Graduations………………………….0.000050″
Grinding Wheel Size……………………………………….10″ Diameter
Grinding Wheel Bore Size………………………………………..1-1/4″
Wheelhead Motor…………………………………………….1-1/2 H.P.
Headstock Swivel……………………………………….0 to 90 Degrees
Infinite Variable Headstock Spindle Speeds………………….20 to 225 RPM
Hole Thru Spindle………………………………………………1-1/4″
Headstock Center Taper………………………………………..#6 Jarno
Tailstock Center Taper………………………………………..#6 Jarno
Spindle Motor………………………………………………1-1/5 H.P.
Electrics………………………………………………..480/3/60
Approximate Dimensions……………………………….69″L x 37″L x 57″H
Approximate Weight………………………………………….3,750 Lbs.
EQUIPPED WITH:
O.D. Wheelhead, Presently is Set-Up to use 10″ Diameter Wheel, 3″ Bore
Swing-Around Internal Grinding Attachment with I.D. Spindle
Tailstock Center and Workhead Center
Parker-Majestic Super-Precision Spindle for Wheelhead
Coolant System, Self-Contained, in the Base of the Machine
One-Shot Lubricator
Acu-Rite II Digital Readout
12″ X 24″ PARKER-MAJESTIC “SUPER-PRECISION” (MADE IN USA) I.D./O.D. CYLINDRICAL GRINDER REBUILT 2024
MODEL: 1C S/N: 6154-1C-96
NEW: 1996
SWING OVER TABLE …………………… 12″
DISTANCE BETWEEN CENTERS ……………. 24″
TABLE WORKING SURFACE ………………. 5″ X 41″
POWER TABLE SPEEDS …………………. 3″ TO 30″ IPM
TABLE SWIVEL ………………………. 7 DEGREES
TABLE TRAVEL ………………………. 24″
CROSS FEED TRAVEL ………………….. 3- 1/2″
CROSS FEED ADJUSTMENT ………………. 4″
CROSS FEED HANDWHEEL GRAD. ………….. 0.0005″
CROSS FEED PRECISION DIAL GRAD ………. 0.000050″
GRINDING WHEEL SIZE ………………… 12″ DIAMETER
HEADSTOCK SWIVEL …………………… 0 TO 90 DEG.
INFINETLY VARIABLE HEADSTOCK SPINDLE
SPEEDS ………………………….. 50 TO 450 RPM
DEAD CENTER SPEEDS …………………. 20 TO 225 RPM
HOLE THRU SPINDLE ………………….. 1- 1/4″
HEADSTOCK CENTER TAPER ……………… #6 JARNO
TAILSTOCK CENTER TAPER ……………… #6 JARNO
APPROX. DIMENSIONS …………………. 91″L X 48″D X 65″H
APPROX. MACHINE WEIGHT ……………… 3,000 LBS.
EQUIPPED WITH:
SWING-AROUND INTERNAL GRINDING ATTACHMENT SPINDLE
PARKER-MAJESTIC SUPER-PRECISION SPINDLE FOR WHEELHEAD
MACHINE PRESENTLY HAS A 12″ DIAMETER x 1″ WIDE WHEEL
ELECTRONIC INFINITLEY VARIABLE SPEED CONTROL FOR WORKHEAD
SPINDLE SPEEDS
VARIABLE SPEED ELECTRIC TABLE DRIVE FOR QUIET & SMOTH OPERATION
TABLE SINE OPTION FOR ACCURATE TAPER GRINDING
WORKHEAD ACCEPTS 5C COLLETS
.00005″ CROSS FEED DIAL GRADUATIONS
5″ BUILT-IN WORKHEAD SINE BAR
COOLANT SYSTEM, SELF-CONTAINED, IN THE BASE OF THE MACHINE
“BIJUR” ONE-SHOT LUBRICATOR
1 H.P./3/60/230-460 VOLT MOTOR FOR THE WORKHEAD
3 H.P./3/60/230-460 VOLTS MOTOR FOR THE GRINDING WHEELHEADS
MACHINE IS PRESENTLY WIRED FOR 3/60/460 VOLTS
MAGNETIC CHUCK
Accurate 2 Axis DRO
INSPECT UNDER POWER
Scope of Remanufacturing – 2024
Rebuilt motor drive VARI-Speed on headstock
Rebuilt motor drive VARI-Speed on table drive
New lead screw in cross slide
New One Shot Lube System
ALL NEW ELECTRICS IN PANEL, PUSH BUTTONS, AND MOTORS
COMPLETELY FLAKED & SCRAPPED TO NEW TOLERANCE
SPINDLES REBUILT
Parker Majestic Internal Grinder
SPECIFICATIONS:
Swing: 14″
Table Distance: 28″
Variable Speed Workhead
Power Table Feed
5″ Sine Bar Headstock
Graymills Coolant System
220/3.60 Electrics
Schaudt Universal OD / ID Grinder
Model: E450 U1000
SPECIFICATIONS:
Center height 180 mm / 7 inches
Distance between centers 1120 mm / 44.8 inches
max.grinding length 1040 mm / 40.9 inches
large workpiece diameter 350 mm / 13.77 inches
Grinding wheel dimensions 400x63x127 mm
The table can be swiveled by 9 °
Speed of grinding spindle 32 m / s
Drive power grinding spindle 5.5 kW
Weight approx. 4500 kg
Swing around Internal grinding device
Encyclon Inc. coolant system
Hydraulic tailstock
Misc. New Grinding Wheels & Tooling
(1) USED LANDIS 10” X 20” 1R UNIVERSAL CYLINDRICAL GRINDER W/ ID ATTACHMENT
Serial Number: 875-45
SPECIFICATIONS:
Nominal work swing: 10”
Nominal distance between centers: 20”
Table traverse speed: 2 to 240 IPM
Grinding wheel size: 12” diameter x 1” wide x 5” hole
Grinding wheel max width: 1.5”
Grinding wheel spindle motor: 5 HP
Workhead speeds: 30 to 150 RPM
Grinding wheelhead swivel: upper & lower : 90 Degrees each way
Headstock center: #10 Jarno
Footstock center: #6 Jarno
Footstock center movement: lever operated
Diameter of hole in spindle: 1”
Headstock swivel: 120 Degrees
Headstock spindle nose: 5A-2
EQUIPPED WITH:
Swing Down ID Spindle
Plunge Cycle
Table Traverse
Tarry timers left and right reversal
Attached electrical panel
Parker Majestic Internal Grinder
SPECIFICATIONS:
12″ Swing
16″ Stroke
Power Table Travel
Forward & Reversing Headstock
5″ Sine Attachment on Headstock
One Shot Lubrication
Coolant in Base w/ Pump
(1) USED HEALD 273A UNIVERSAL INTERNAL GRINDER
Model: 273A
Serial Number: 42180
SPECIFICATIONS:
Swing over table: 24.5″″
Hole length ground: 16”
Max Table Travel: 20”
Hole diamter ground: 18”
Included angle taper: 180 Degrees
Grinding speed: 0 – 18 FPM
Workhead Speed: 0 – 500 RPM ( Variable )
Crossfeed Increments: .0001” – .0005”
EQUIPPED WITH:
Red Head Spindle – RPM / TBD
4 position stop
Hydrostatic ways
Cross sliding workhead
Dresser
Sine bar attachment
12″ T-Slotted Face Plate
Coolant Tank & Pump
220/3/60 Electrics
Parker Majestic Internal Grinding Spindle
50,000 RPM Max Speed
Style 2252-3
Serial No. 38226
Completely Rebuilt 2022
90 Day Warranty
