| By admin | 0 Comments
Moore G-18 Jig Grinder
Moore Model: G-18
S/N# G-2194
SPECIFICATIONS:
11″ x 24″ Table
Travel 11″ x 18″
Table top to wheel collet 2″ to 18
Spindle to column ways 10″
Max spindle speed 40,000 rpm
Grinding capacity 3/16″ to 5″
Sony 2 axis DRO
(2) Additional Grinding Spindle Heads Available
| By admin | 0 Comments
Parker Majestic 14″ x 30″ 2C Universal Cylindrical / Internal Grinder
Serial Number: 00069-2C-05
New: 2005
SPECIFICATIONS:
14″ Swing
30″ Distance Between Centers
OD Grinding Wheel: 12″ x 1″ x 5″
1 HP Variable Speed Headstock
5 HP Variable Speed OD Grinding Wheel Drive
3 HP Variable Speed ID Grinding Wheel Drive
Variable Speed Table Traverse
Manual Driven Ballscrew Cross feed – Hand Wheel Graduated “.0005 – Precision Graduated .00005”
7º Table Swivel
90º Headstock Swivel
One Shot Lubrication
Attached Electrical Panel – 480 V / 60 / 3
EQUIPPED WITH:
5″ Sine Bar Headstock
Heidenhain Digital Read Out
Paper Filtration System w/ Gusher Pump & Tank
3 Point Center Rest
8″ 3 Jaw Chuck
10″ Magnetic Chuck
Splash Guards
Machine Dimensions:
104″ x 41″ x 46″
Approx Weight: 5200 LBS.
| By admin | 0 Comments
GER Universal OD Grinder w/ ID Attachment
Model: RHC-1000
Serial Number: 82/2008
SPECIFICATIONS:
Swing: 12″
Center Distance: 40″
Grinding Wheel Motor: 5 HP
Internal Grinding Spindle Motor: 1 HP
OD Grinding Wheel Size: 16″ Did x 5″ Width x 5″ Hole
Headstock Drive Motor: 1 HP
Hydraulic Pump: 1.5 HP
Pickfeed at Table Reversal
Automatic Plunge Cycle
Manual Tailstock
Coolant Tank & Pump
Internal Grinding Attachment w/ Spindle
Coolant Tank & Pump
220/3/60
Operators Manuals & Prints
| By admin | 0 Comments
GER Universal OD Grinder w/ ID Attachment
Model: RHL-600
Serial Number: 81 / 91
SPECIFICATIONS:
Swing: 10″
Center Distance: 24″
Grinding Wheel Size: 16″ x 3″ x 5″
Grinding Wheel Motor: 5.5 HP
Work Head Drive Motor: 1 HP
Hydraulic Motor: 1.5 HP
Plunge Cycle
Pick Feed at Table Reversal
Internal Grinding Spindle Attachment
Coolant Pump & Tank
220/3/60
Approx Weight: 5,500LBS.
| By admin | 0 Comments
Chevalier Universal Cylindrical OD Grinder
Model: CGP-816
Serial Number: 2040317
Condition: Like New
Operating Hours: 142
Purchased New in 2010
Control Type: Mitsubishi Pro-Face Digital w/ DRO
PLC controls the In-Feed Functions, Rapid, Rough & Fine Feeds & Retraction at end of Cycle
Spindle Head: MT:3 / +
Attachment for Chuck
1/4 HP Coolant Pump System
Magnetic Coolant Separator 20L
Paper Band Filter 20L
Table Swivel Angle: -3º, +12º
Distance between Centers: 15.7º
Swivel over Table: 7.9”
Max. load between centers: 132lbs
Max. External Grinding: 7.09”
Wheel Head Swivel Angle: ±30º
Wheel Head Manual Distance: 5.2”
Wheel Size: Ø12” OD x 1.5” W x Ø5” ID
Wheel Speed: 60Hz: 2,495 RPM
Wheel Spindle Motor: 3 HP
Spindle Speed: 10 – 300 RPM
Workhead Spindle Motor: 1HP
Manual Tailstock
Currently Set Up with a Collet Fixture on Headstock, Centers available with Machine
Power: 23A/230V, 3-Phase
Overall Dimensions: 86.6”L x 70”W x 60.7”H
Weight: 4,400lbs
| By admin | 0 Comments
Parker Majestic 14″ x 30″ 1C OD / ID Combination Cylindrical Grinder
Model: 1C
Serial Number: 6314-1C-99
New: 1999
GENERAL CATALOG SPECIFICATIONS
OVERALL DIMENSIONS (WXDXH) 104 IN X 41 IN X 46 IN
MACHINE WEIGHT (NET) 5200 LBS (2358 KG)
MAX PART DIAMETER 14 IN (355.6 MM)
DISTANCE BETWEEN CENTERS 30 IN (762 MM )
WORKTABLE SIZE 5 IN X 50 IN (127 MM X 1270 MM)
TABLE SWIVEL 7 DEGREES
WORKHEAD SPINDLE
SPEED 0-1000 RPM
SPINDLE NOSE PARKER TAPER – ACCEPTS 5C COLLETS
DRIVE MOTOR 1 HP@1,750/200 RPM
MANUALLY PIVOTING WORKHEAD (B-AXIS) – ACCURACY 0.0005 DEGREES
POWER
POWER REQUIREMENT 230, OR 480 VAC – 50/60 HZ
POWER CONSUMPTION 6 KVA
MAX. CURRENT 30 A
TOTAL POWER RATING 10 HP (7.5 KW)
TABLE AXIS
MANUAL AND VARIABLE SPEED ELECTRIC TABLE DRIVE
HAND SCRAPED TURCITE COATED VEE & FLAT WAY SYSTEM
TOTAL TRAVEL 30 IN (762 MM)
TABLE FEED MOTOR 3/4 HP @ 1,750/400 RPM
TABLE SWIVEL 7 DEGREES
CROSSFEED AXIS
MANUAL DRIVEN BALLSCREW
PRECISION ROLLING ELEMENT LINEAR MOTION BEARING
CLOSED LOOP POSITIONING WITH HEIDENHAIN GLASS SCALE FEEDBACK
TOTAL TRAVEL 7 IN (177.8 MM)
EQUIPPED WITH
SWING AROUND OD / ID UNIVERSAL GRINDING HEAD
14″ DIAMETER GRINDING WHEEL CAPACITY
8″ (6) JAW CHUCK
5″ SINE BAR HEADSTOCK
MANUAL TAILSTOCK
TABLE MOUNTED DRESSER
DANFOSS VTL 2000 VARIABLE SPEED DRIVES
COOLANT PUMP & TANK
ATTACHED ELECTRICAL PANEL 22/3/60
ELECTRICAL DRAWINGS & MANUALS
MACHINE IS IN EXCELLENT CONDITION – (1) ONE OWNER – ORIGINAL SCRAPING & PAINT
SMALL ONE MAN JOB SHOP
| By Momentum | 0 Comments
Springfield 2 ATR Crown Type Vertical Universal Grinder
Serial Number: 68025
35″ Swing
Magnetic Rotary Chuck
(2) Spindle Quills
| By admin | 0 Comments
Okuma Universal Cylindrical Grinder w/ ID Attachment
Type GCU
SN: 4406-0730
Swing: 19″
Distance Between Centers: 47″
Tarry Left & Right at Table Reversal
Auto & Hand Infeed on Grinding Wheel Head
Vary Speed Head Stock: 14-200 RPM
Manual Tail Stock
Swing Down ID Spindle
16″ Grinding Wheel Diameter
Attached Electrics
Self Contained Coolant
| By admin | 0 Comments
12″ X 20″ PARKER-MAJESTIC “SUPER-PRECISION” (MADE IN USA) I.D./O.D. CYLINDRICAL GRINDER
MODEL: 1C S/N: 6228-1C-97
NEW: 1997
SWING OVER TABLE …………………… 12″
DISTANCE BETWEEN CENTERS ……………. 20″
TABLE WORKING SURFACE ………………. 5″ X 41″
POWER TABLE SPEEDS …………………. 3″ TO 30″ IPM
TABLE SWIVEL ………………………. 7 DEGREES
TABLE TRAVEL ………………………. 24″
CROSS FEED TRAVEL ………………….. 3- 1/2″
CROSS FEED ADJUSTMENT ………………. 4″
CROSS FEED HANDWHEEL GRAD. ………….. 0.0005″
CROSS FEED PRECISION DIAL GRAD ………. 0.000050″
GRINDING WHEEL SIZE ………………… 12″ DIAMETER
HEADSTOCK SWIVEL …………………… 0 TO 90 DEG.
INFINETLY VARIABLE HEADSTOCK SPINDLE
SPEEDS ………………………….. 50 TO 450 RPM
DEAD CENTER SPEEDS …………………. 20 TO 225 RPM
HOLE THRU SPINDLE ………………….. 1- 1/4″
HEADSTOCK CENTER TAPER ……………… #6 JARNO
TAILSTOCK CENTER TAPER ……………… #6 JARNO
APPROX. DIMENSIONS …………………. 91″L X 48″D X 65″H
APPROX. MACHINE WEIGHT ……………… 3,000 LBS.
EQUIPPED WITH:
SWING-AROUND INTERNAL GRINDING ATTACHMENT WITH A P-M I.D. SPINDLE
PARKER-MAJESTIC SUPER-PRECISION SPINDLE FOR WHEELHEAD
MACHINE PRESENTLY HAS A 12″ DIAMETER x 1″ WIDE WHEEL, “NORTON” No. 32A80-KVBE
PARKER-MAJESTIC MODEL No. 3090 WORKHEAD, S/N: 59686
ELECTRONIC INFINITLEY VARIABLE SPEED CONTROL FOR WORKHEAD
SPINDLE SPEEDS
VARIABLE SPEED ELECTRIC TABLE DRIVE FOR QUIET & SMOTH OPERATION
TABLE SINE OPTION FOR ACCURATE TAPER GRINDING
TEFLON COATED LONGITUDINAL WAYS
LIVE/DEAD WORKHEAD SPINDLE
RIGID DEAD CENTER DRIVE
WORKHEAD ACCEPTS 5C COLLETS
8″ DIAMETER “BUCK FORKHARDT” 4-JAW CHUCK
.00005″ CROSS FEED DIAL GRADUATIONS
5″ BUILT-IN WORKHEAD SINE BAR
COOLANT SYSTEM, SELF-CONTAINED, IN THE BASE OF THE MACHINE
“BIJUR” ONE-SHOT LUBRICATOR
1 H.P./3/60/230-460 VOLT MOTOR FOR THE WORKHEAD
3 H.P./3/60/230-460 VOLTS MOTOR FOR THE GRINDING WHEELHEADS
MACHINE IS PRESENTLY WIRED FOR 3/60/460 VOLTS
INSPECT UNDER POWER
EXCEPTIONAL CONDITION & APPEARANCE – ORIGINAL PAINT
| By admin | 0 Comments
(1) USED LANDIS 10” X 20” 1R UNIVERSAL CYLINDRICAL GRINDER W/ ID ATTACHMENT
Serial Number: 864-70
SPECIFICATIONS:
Nominal work swing: 10”
Nominal distance between centers: 20”
Table traverse speed: 2 to 240 IPM
Grinding wheel size: 12” diameter x 1” wide x 5” hole
Grinding wheel max width: 1.5”
Grinding wheel spindle motor: 5 HP
Workhead speeds: 30 to 150 RPM
Grinding wheelhead swivel: upper & lower : 90 Degrees each way
Headstock center: #10 Jarno
Footstock center: #6 Jarno
Footstock center movement: lever operated
Diameter of hole in spindle: 1”
Headstock swivel: 120 Degrees
Headstock spindle nose: 5A-2
EQUIPPED WITH:
Swing Down ID Spindle
Table Traverse
Attached electrical panel
Coolant Tank & Pump
Machine has been Stripped down, Cleaned and Scheduled to be Repainted
Table Ways have been Scraped
