LANDIS 18″ X 96″ MDL. 3R Universal Cylindrical Grinder
Serial Number: 796-84
18″ Swing
96″ Between Centers
2″ x 18″ Grinding Wheel Capacity
2 -240 IPM Traverse Table Speed
0.0003″ – 0.004″ Infeed at Table Reversal
0.100″ Handwheel Graduation
0.005″ Fine Feed
Variable Speed Work Head
120 Deg. Swivel Work Head
5 HP Wheelhead Drive Motor
EQUIPPED WITH:
(5) 2 pt. Steadyrests,
ALL NEW Electrical Cabinet, New Variable Speed Drive & Motor for Headstock, All Electric Motors Rebuilt
Cincinnati Universal OD/ID Grinder
18″ Swing
48″ Distance Between Centers
Pickfeed at Table Reversal
Tarry Timers Left & Right
Variable Speed Headstock
Digital Readout
Swing Down ID Attachment
Manual Tailstock
3 Jaw Chuck
Table, Bed & Cross Slides have been Ground, Scraped & Flakes
Rebuilt ID Spindle
Backlash Eliminator on Feed Screw
14” x 96” Cincinnati Universal OD / ID Grinder
Serial Number: 3U4F5R-3
14” Swing
96” Center Distance
14” Diameter Grinding Wheel
Dayton A/C Inverter Vari Speed -Grinding Wheel
Variable Speed Headstock
Manual Tailstock
Tarry Timer Left & Right
Table Traverse
Pick Feed Left & Right
Coolant in Base w/ Pump
Attached Electrical 240V
Table Ways Have been Broken Up & Flaked 2018
Manuals
- ID Internal Grinding Attachment
10″ X 24″ BROWN & SHARPE UNIVERSAL CYLINDRICAL GRINDER
MODEL: 1024U
SWING OVER TABLE: 10″
DISTANCE BETWEEN CENTERS, NOMINAL: 24″
DISTANCE BETWEEN CENTERS, MAXIMUM: 26-3/4″
WHEELHEAD SPINDLE SPEEDS (3) …… 2100, 2400& 2800 RPM
GRINDING WHEEL SIZE …………………… 12″ X 1″ X 5″
MINIMUM GRINDING WHEEL WIDTH …………………… 3/8″
SWIVEL AT THE WHEELSLIDE ……….. 90 DEGREES EITHER WAY
WHEEL SPINDLE SWIVELS ………….. 90 DEGREES EITHER WAY
INFINITELY VARIABLE SPINDLE SPEEDS …….. 60 TO 600 RPM
HEADSTOCK SPINDLE NOSE TAPER ………………….. A2-5″
HEADSTOCK SWIVELS EITHER SIDE OF ZERO ……… 90 DEGREES
INFINITELY VARIABLE TABLE SPEED ………. 3″ TO 150″ IPM
TABLE PER REV. OF HANDWHEEL:
SLOW ………………………………………… 0.1″
FAST ………………………………………… 1.5″
DWELL AT EACH OR ALTERNATE TABLE REV. ….. 0 – 2-1/2 SEC.
TABLE SWIVEL, SCALES FOR ANGULAR SETTING …… 8-1/4 DEG.
SCALES-TAPER PER FT. ………………………… 3-1/2″
MAX. TRAVEL OF WHEELSLIDE ………………………. 5″
CROSSFEED HANDWHEEL GRAD. ………………….. 0.00002″
AUTOMATIC CROSS FEED, REDUCTION IN DIAMETER
OR WORK AT EACH OR ALTERNATE REVERSALS .. 0.0001″ – .003″
HAND FEED PER REV. OF HANDWHEEL:
SLOW ………………………………………… 0.1″
FAST ………………………………………… 0.3″
TAILSTOCK SPINDLE TAPER …………………….#7 JARNO
TAILSTOCK SPINDLE TRAVEL ………………………. 5/8″
APPROXIMATE WEIGHT ………………………. 5,100 LBS
MACHINE FEATURES:
DUAL RIGHT OR LEFT END WHEEL MOUNTING
SWIVELLING AT WHEEL SPINDLE HEAD OR AT THE WHEEL
SLIDE PERMITS ANY COMPOUND SETTING REQUIRED IN
COMBINATION STRAIGHT AND TAPER GRINDING,
EXTERNAL OR INTERNAL ( no Internal Assembly ).
INFEED HANDWHEEL GRADUATED TO READ TO 0.000020″
HYDRAULIC TABLE TRAVERSE
AUTO INFEED OF WHEELHEAD @ TABLE REVERSALS
POWER RAPID WHEELHEAD ADVANCE & RETRACTION
ADJUSTABLE TABLE DWELL
SELF-CONTAINED HYDRAULIC SYSTEM
EQUIPPED WITH:
B & S “HYDROSTATIC” WORKHEAD w/DUAL DEAD/LIVE
HEADSTOCK SPINDLE
COOLANT SYSTEM
MOTORS ARE 3/60/230-460 VOLTS
Cincinnati 18 x 72 DE Universal OD Grinder
18″ Swing
72″ Between Centers
20” Diameter Grinding Wheel
Attached Electrical
Coolant in base w/ Pump
Tarry Timer Left & Right at Table Reversal
Pickfeed Left & Right at Table Reversal
Variable Speed Headstock
Ways in good shape
440/3/60
Guarding & Wheels for standard 14”
(1) USED LANDIS 10” X 20” 1R UNIVERSAL CYLINDRICAL GRINDER
Serial Number: 875-28
Stock Number: 2136
SPECIFICATIONS:
Nominal work swing: 10”
Nominal distance between centers: 20”
Table traverse speed: 2 to 240 IPM
Grinding wheel size: 12” diameter x 1” wide x 5” hole
Grinding wheel max width: 1.5”
Grinding wheel spindle motor: 5 HP
Workhead speeds: 30 to 150 RPM
Grinding wheelhead swivel: upper & lower : 90 Degrees each way
Headstock center: #10 Jarno
Footstock center: #6 Jarno
Footstock center movement: lever operated
Diameter of hole in spindle: 1”
Headstock swivel: 120 Degrees
Headstock spindle nose: 5A-2
EQUIPPED WITH:
Plunge cycle
Table Traverse
Tarry timers left and right reversal
Manual tailstock
Attached electrical panel
Coolant Pump & Tank
Parker Majestic 1C Combination ID / OD Universal Grinder
Serial Number: 2467.1C.86
SPECIFICATIONS:
12″ x 24″ Capacity
5″ Sine Bar
Headstock VARI-speed
OD. Spindle ( runs very quiet )
ID. Spindle. ( runs very quiet )
Tailstock hand operated
Coolant pump & tank
(1) axis digital read out
Power table VARI- speed
Center drive attachment for dead center drive
4jaw Chuck
Face Plate
TABLE WAYS LOOK GOOD
LANDIS 14″ X 96″ MDL. 3RH Universal Cylindrical Grinder
Serial Number: 796-87
14″ Swing
96″ Between Centers
2″ x 18″ Grinding Wheel Capacity
2 -240 IPM Traverse Table Speed
0.0003″ – 0.004″ Infeed at Table Reversal
0.100″ Handwheel Graduation
0.005″ Fine Feed
Live & Dead Center Heavy Duty Work Head
800 lbs. Work Weight Capacity
120 Deg. Swivel Work Head
#14 Jarno Taper Work Head
#10 Jarno Taper Tail Stock
5 HP Wheelhead Drive Motor
EQUIPPED WITH:
(5) 2 pt. Steadyrests, (1) 3 pt. Steadyrest
(2) Back Rests
12″ Dia. 4-Jaw Chuck
Balance Arbor
Coolant System w/ Magnetic Separator
assorted collets
assorted table guarding
Spindle Rebuilt
14″ X 36″ Landis Universal Grinder
S/N. 796-57
Head stock. VARI-speed controller
Tail stock. ( hand operated)
Auto-plunge feed
Hydraulic table travel with pick feed
Tarry Timer Left & Right
BIJUR One ShotLubrication pump ( hand operated)
Electrical panel attached to machine
FROM. AREO-SPACE GEAR PLANT
RUNS VERY GOOD
Landis 14″ x 72″ 3RH Universal OD Grinder w/ ID Grinding Attachment
Serial Number: 867-92
SPECIFICATIONS:
Swing: 14″
Distance Between Centers: 72″
Table Traverse Speeds: 2-240 IPM
Grinding Wheel Size: 14″ x 1.5″ x 5″
Grinding Wheeled Swivel: 180˙
Automatic Infeed at Table Reversal: 0.000″ – 0.004″
Headstock Center: #14 Jarno
Tailstock Center: #10 Jarno
Headstock Speeds: 12-72 RPM Low ( Variable )
60-260 High ( Variable )
Headstock Swivel: 120˙
Spindle Motor: 5HP
Headstock Motor: 1HP
EQUIPPED WITH:
Internal Grinding Spindle Attachment – 15,000 RPM
Industrial Filters Deep Bed Coolant Filtration System – Paper
Free Standing Electrical Panal
Machine Floor Space: 74″ x 229″
Machine Weight: 12,300 LBS
