Okuma 19″ x 48″ Universal OD Grinder w/ ID Attachment

  |   By  |  0 Comments

IMG

Okuma Universal Cylindrical Grinder w/ ID Attachment

Type GCU
SN: 4406-0730
Swing: 19″
Distance Between Centers: 47″
Tarry Left & Right at Table Reversal
Auto & Hand Infeed on Grinding Wheel Head
Vary Speed Head Stock: 14-200 RPM
Manual Tail Stock
Swing Down ID Spindle
16″ Grinding Wheel Diameter
Attached Electrics
Self Contained Coolant

Parker Majestic 1C Universal ID / OD Grinder

  |   By  |  0 Comments

Parker Majestic 1C Universal ID / OD Grinder

12″ X 20″ PARKER-MAJESTIC “SUPER-PRECISION” (MADE IN USA) I.D./O.D. CYLINDRICAL GRINDER

MODEL: 1C S/N: 6228-1C-97
NEW: 1997

SWING OVER TABLE …………………… 12″
DISTANCE BETWEEN CENTERS ……………. 20″
TABLE WORKING SURFACE ………………. 5″ X 41″
POWER TABLE SPEEDS …………………. 3″ TO 30″ IPM
TABLE SWIVEL ………………………. 7 DEGREES
TABLE TRAVEL ………………………. 24″

CROSS FEED TRAVEL ………………….. 3- 1/2″
CROSS FEED ADJUSTMENT ………………. 4″
CROSS FEED HANDWHEEL GRAD. ………….. 0.0005″
CROSS FEED PRECISION DIAL GRAD ………. 0.000050″

GRINDING WHEEL SIZE ………………… 12″ DIAMETER

HEADSTOCK SWIVEL …………………… 0 TO 90 DEG.
INFINETLY VARIABLE HEADSTOCK SPINDLE
SPEEDS ………………………….. 50 TO 450 RPM
DEAD CENTER SPEEDS …………………. 20 TO 225 RPM
HOLE THRU SPINDLE ………………….. 1- 1/4″
HEADSTOCK CENTER TAPER ……………… #6 JARNO
TAILSTOCK CENTER TAPER ……………… #6 JARNO

APPROX. DIMENSIONS …………………. 91″L X 48″D X 65″H
APPROX. MACHINE WEIGHT ……………… 3,000 LBS.

EQUIPPED WITH:
SWING-AROUND INTERNAL GRINDING ATTACHMENT WITH A P-M I.D. SPINDLE
PARKER-MAJESTIC SUPER-PRECISION SPINDLE FOR WHEELHEAD
MACHINE PRESENTLY HAS A 12″ DIAMETER x 1″ WIDE WHEEL, “NORTON” No. 32A80-KVBE
PARKER-MAJESTIC MODEL No. 3090 WORKHEAD, S/N: 59686
ELECTRONIC INFINITLEY VARIABLE SPEED CONTROL FOR WORKHEAD
SPINDLE SPEEDS
VARIABLE SPEED ELECTRIC TABLE DRIVE FOR QUIET & SMOTH OPERATION
TABLE SINE OPTION FOR ACCURATE TAPER GRINDING
TEFLON COATED LONGITUDINAL WAYS
LIVE/DEAD WORKHEAD SPINDLE
RIGID DEAD CENTER DRIVE
WORKHEAD ACCEPTS 5C COLLETS
8″ DIAMETER “BUCK FORKHARDT” 4-JAW CHUCK
.00005″ CROSS FEED DIAL GRADUATIONS
5″ BUILT-IN WORKHEAD SINE BAR
COOLANT SYSTEM, SELF-CONTAINED, IN THE BASE OF THE MACHINE
“BIJUR” ONE-SHOT LUBRICATOR
1 H.P./3/60/230-460 VOLT MOTOR FOR THE WORKHEAD
3 H.P./3/60/230-460 VOLTS MOTOR FOR THE GRINDING WHEELHEADS
MACHINE IS PRESENTLY WIRED FOR 3/60/460 VOLTS

INSPECT UNDER POWER
EXCEPTIONAL CONDITION & APPEARANCE – ORIGINAL PAINT

Landis 1R Universal OD Grinder w/ ID Attachment

  |   By  |  0 Comments

IMG

(1) USED LANDIS 10” X 20” 1R UNIVERSAL CYLINDRICAL GRINDER W/ ID ATTACHMENT
Serial Number: 864-70

SPECIFICATIONS:
Nominal work swing: 10”
Nominal distance between centers: 20”
Table traverse speed: 2 to 240 IPM
Grinding wheel size: 12” diameter x 1” wide x 5” hole
Grinding wheel max width: 1.5”
Grinding wheel spindle motor: 5 HP
Workhead speeds: 30 to 150 RPM
Grinding wheelhead swivel: upper & lower : 90 Degrees each way
Headstock center: #10 Jarno
Footstock center: #6 Jarno
Footstock center movement: lever operated
Diameter of hole in spindle: 1”
Headstock swivel: 120 Degrees
Headstock spindle nose: 5A-2

EQUIPPED WITH:
Swing Down ID Spindle
Table Traverse
Attached electrical panel
Coolant Tank & Pump

Machine has been Stripped down, Cleaned and Scheduled to be Repainted
Table Ways have been Scraped

Cincinnati 12″ x 48″ Universal Cylindrical OD Grinder

  |   By  |  0 Comments

IMG e

Cincinnati 12″ x 48″ Universal Cylindrical OD Griner
Serial Number: 2U3P5D-7
Stock Number: 2124

SPECIFICATIONS:
12″ swing over table
48″ between centers
Headstock. VARI-speed
Tailstock. ( hand operated )
Self contained coolant pump & tank
Attached electrical panel
16″ dia. Grinding wheel

Pick Feed
Tarry Timer L-LR-R at Reversal

Springfield 3 1/2 Rail Type Vertical Universal ID Grinder

  |   By  |  0 Comments

Springfield 3 1/2 Rail Type Vertical Universal ID Internal Grinder

Springfield 3 1/2 Rail Type Vert Universal Grinder

Serial Number: 74075

Single Universal Spindle – 36″ Stroke
48″ of Vertical Travel
62″ Slotted Table
72″ Swing inside of Guards
Table speeds from 1 to 180 RPM
Table load capacity: 10,000#
Elevating rail travel: 36″
Rail to table: 12″ min., 48″ max.
Grinding slide swivels: 45 degrees in either direction Grinding slide cross
travel: 78″
Machine equipped with:
Dresser attachment
Grinding spindle, 33″long
10 HP Spindle Motor
Pendant Control
Coolant
Power clamping on rail
Pendant control
Dimensions: FB X RL – 120″ X 142″
Height: 175″
Est. weight: 50,000#

Work Preformed by Bourn & Koch
The following work was completed in 2013:

–       New ball screws and grinding spindle motor
–       In-field rebuild of the slide
–       Repair of leaking cylinders

In total, there was about $50K worth of parts and service put into the machine from 2007-2013
The machine has never ran any jobs since being put back on-line in 2013.

Kellenberger 600U Universal OD Grinder

  |   By  |  0 Comments

IMG

Kellenberger 600U Universal OD Grinder
Model: 600U
Serial Number: 32459-2127

SPECIFICATIONS:

Height of Centers, as Presently Configured …………………………6.75″
Nominal Swing …………………………………………………….13″
Distance between Centers (Nominal)……………………………….23-5/8″
Distance between Centers w/Tailstock Overhanging ………………….29-1/2″

Table:
Longitudinal Table Travel…………………………………………..27″
Longitudinal Table Travel per Handwheel Turn – Coarse……………….25/32″
Longitudinal Table Travel per Handwheel Turn – Fine………………….3/32″
Longitudinal Table Speed – Hydraulic………………………0.06 to 18′ FPM
Table Swivels……………………………………………….11 Degrees
Reversing Dwell…………………………………………..0 – 5 Seconds

Grinding Wheel Infeed:
1 Graduation of Feed Scale………………………………………0.0002″
Automatic Feed – Maximum…………………………………………0.035″
Automatic Infeed Per Table Reversal………………………0.00005″ – 0012″
Infeed for Plunge Grinding………………………………0.00004″ – .002″
Plunge Grinding – Infeed Speed……………………….10 – 1000 uIN/Second
Micrometer Stop, 1 Graduation…………………………………..0.00005″

Universal Grinding Spindle Head:
Transverse Movement of Wheel Slide……………………………….11-1/4″
Hydraulic Rapid Wheel Slide Advance/Retraction Stroke………………1-9/16″
Grinding Wheel Speeds – RPM (4)……………………1500, 1700, 2220 & 3600
Grinding Wheel for Cylindrical Grinding……………………..16″ X 2″ X 5″
Grinding Wheel – Surface Grinding…………………………10″ X 3/4″ X 3″
Swivel of Grinding Head w/Locking Every 90 Degrees……………..270 Degrees
Vert. Motion of Grinding Spdl Head, Height of Centers…..4-59/64″ – 13-25/32″

Workhead:
Spindle Speeds – Infinitely Variable ………………………..10 – 400 RPM
Workhead Swivels……………………………………………360 Degrees
Inside Taper of Work Spindle………………………………………#5 MT

Approximate Floor Space Required…………………………102″ X 64″ X 66″
Approximate Weight…………………………………………..6,000 Lbs.

EQUIPPED WITH:
Hydraulic Operation Featuring: Single Lever Control, Infinitely Variable Table
Traverse, Automatic Feed, Plunge Feed, Rapid Wheel Advance & Retraction
Sparkout Timer

Landis 24″ x 36″ 3RH Universal OD Grinder

  |   By  |  0 Comments

IMG

Landis 3RH Universal OD Grinder

24″ Swing
36″ Between Centers
2″ x 18″ Grinding Wheel Capacity
2 -240 IPM Traverse Table Speed
0.0003″ – 0.004″ Infeed at Table Reversal
0.100″ Handwheel Graduation
0.005″ Fine Feed
Variable Speed Work Head
120 Deg. Swivel Work Head
Tarry at Table Reversal L-LR-R
Plunge Feed

Parker Majestic 16C Universal OD / ID Grinder

  |   By  |  0 Comments

IMG

Parker Majestic 16C Universal OD / ID Grinder
Serial No. 2071-16C-68

SPECIFICATIONS:

Swing Over Table………………………………………………….12″
Distance Between Centers…………………………………………..16″
Table Working Surface…………………………………………5″ x 38″
Power Table with Reciprocator………………………………………Yes
Tabel Swivel………………………………………………..7 Degrees
Table Travel……………………………………………………..24″
Cross Feed Travel………………………………………………3-1/2″
Cross Feed Adjustment………………………………………………4″
Cross Feed Handwheel Graduations………………………………..0.0005″
Cross Feed Precision Dial Graduations………………………….0.000050″
Grinding Wheel Size……………………………………….10″ Diameter
Grinding Wheel Bore Size………………………………………..1-1/4″
Wheelhead Motor…………………………………………….1-1/2 H.P.
Headstock Swivel……………………………………….0 to 90 Degrees
Infinite Variable Headstock Spindle Speeds………………….20 to 225 RPM
Hole Thru Spindle………………………………………………1-1/4″
Headstock Center Taper………………………………………..#6 Jarno
Tailstock Center Taper………………………………………..#6 Jarno
Spindle Motor………………………………………………1-1/5 H.P.
Electrics………………………………………………..220/3/60

Approximate Dimensions……………………………….69″L x 37″L x 57″H
Approximate Weight………………………………………….3,750 Lbs.

EQUIPPED WITH:
O.D. Wheelhead, Presently is Set-Up to use 10″ Diameter Wheel, 3″ Bore
Swing-Around Internal Grinding Attachment with I.D. Spindle
Power Table Option with Reciprocator Feature
Tailstock Center and Workhead Center
Parker-Majestic Super-Precision Spindle for Wheelhead
Parker-Majestic Live/Dead Workhead, Spindle Model No. 2300-3
Workhead Accepts 5C Collets
Coolant System, Self-Contained, in the Base of the Machine
“Bijur” One-Shot Lubricator

Parker Majestic 16C Universal OD / ID Grinder

  |   By  |  0 Comments

Parker Majestic 16C Universal OD / ID Grinder – Reconditioned
Serial No. 2208-16C-75
Reconditioned – 2020

SPECIFICATIONS:

Swing Over Table………………………………………………….12″
Distance Between Centers…………………………………………..16″
Table Working Surface…………………………………………5″ x 38″
Power Table with Reciprocator………………………………………Yes
Tabel Swivel………………………………………………..7 Degrees
Table Travel……………………………………………………..24″
Cross Feed Travel………………………………………………3-1/2″
Cross Feed Adjustment………………………………………………4″
Cross Feed Handwheel Graduations………………………………..0.0005″
Cross Feed Precision Dial Graduations………………………….0.000050″
Grinding Wheel Size……………………………………….10″ Diameter
Grinding Wheel Bore Size………………………………………..3″
Wheelhead Motor…………………………………………….1-1/2 H.P.
Headstock Swivel……………………………………….0 to 90 Degrees
Infinite Variable Headstock Spindle Speeds………………….20 to 225 RPM
Hole Thru Spindle………………………………………………1-1/4″
Headstock Center Taper………………………………………..#6 Jarno
Tailstock Center Taper………………………………………..#6 Jarno
Spindle Motor………………………………………………1-1/5 H.P.
Electrics………………………………………………..220/3/60

Approximate Dimensions……………………………….69″L x 37″L x 57″H
Approximate Weight………………………………………….3,750 Lbs.

EQUIPPED WITH:
Swing-Around Internal Grinding Attachment with I.D. Spindle ( 15,000 Max RPM )
Power Table Option with Reciprocator Feature
Tailstock Center and Workhead Center
Parker-Majestic Super-Precision Spindle for Wheelhead
Parker-Majestic Live/Dead Workhead, Spindle Model No. 2300-3
Workhead Accepts 5C Collets
Coolant System, Self-Contained, in the Base of the Machine
One-Shot Lubricator

Reconditioned 2020
Table, Bed & Infeed Slides Ways – Ground, Scraped & Flaked
New Leadscrew & Nut for the Infeed Slide
New Lubrication Pump, Lines & Meters
Cleaned, Painted & Cycled